| • ioLogik 2542 WL1 Specifications | |
| • Inputs and Outputs | |
| Configurable DIOs (by software) | 12 channels |
| Analog Inputs | 4 channels |
| Isolation | 3k VDC 2k Vrms |
| • Digital Input | |
| Sensor Type | Wet Contact (NPN PNP) and Dry Contact |
| I/O Mode | DI Event Counter |
| Dry Contact | • On: short to GND • Off: open |
| Wet Contact (DI to COM) | • On: 10 to 30 VDC • Off: 0 to 3 VDC |
| Common Type | 6 points per COM |
| Counter Frequency | 2.5 kHz |
| Digital Filtering Time Interval | Software configurable |
| • Digital Output | |
| Type | Sink |
| I/O Mode | DO Pulse Output |
| Pulse Output Frequency | 5 kHz |
| Over-Voltage Protection | 45 VDC |
| Over-Current Protection | 1.5 A per channel @ 25°C |
| Over-Temperature Shutdown | 175°C (min.) |
| Current Rating | 500 mA per channel @ 25°C |
| DIO Output Leakage Current | < 1 mA @ 30 VDC |
| • Analog Input | |
| Type | Differential input |
| Resolution | 16 bits |
| I/O Mode | Voltage / Current (software selectable) |
| Input Range | ±10 V, 0 to 10 V, 0 to 20 mA, 4 to 20 mA, 4 to 20 mA (burnout detection) |
| Accuracy | • ±0.1% FSR @ 25°C • ±0.3% FSR @ -10 and 60°C • ±0.5% FSR @ -30 and 70°C |
| Sampling Rate | • All channels: 400 samples/sec • Per channel: 100 samples/sec |
| Input Impedance | 1M ohms (min.) |
| Built-in Resistor for Current Input | 120 ohms |
| • Power Requirements | |
| Input Voltage | 9 to 48 VDC |
| Input Current | 406 mA @ 24 VDC |
| • MTBF (mean time between failures) | |
| Time | WL1 model: 331,222 hrs |
| Standard | Telcordia SR332 |
| • Common Specifications | |
| • WLAN | |
| Standards | • IEEE 802.11b/g for wireless LAN • IEEE 802.11i for wireless security |
| Spread Spectrum and Modulation (typical) | • DSSS with DBPSK, DQPSK, CCK • OFDM with BPSK, QPSK, 16QAM, 64QAM • 802.11b: CCK @ 11/5.5 Mbps, DQPSK @ 2 Mbps, DBPSK @ 11 Mbps • 802.11g: 64QAM @ 54/48 Mbps, 16QAM @ 36/24 Mbps, QPSK @ 18/12 Mbps, BPSK @ 9/6 Mb |
| Operating Channels (central frequency) | • US: 2.412 to 2.462 GHz (11 channels) • EU: 2.412 to 2.472 GHz (13 channels) |
| Security | • 64-bit and 128-bit WEP encryption • Full WPA/WPA2 Personal |
| Transmission Rates | • 802.11b: 1, 2, 5.5, 11 Mbps • 802.11g: 6, 9, 12, 18, 24, 36, 48, 54 Mbps |
| TX Transmit Power | • 802.11b: Typ. 18±1.5 dBm @ 1 to 11 Mbps • 802.11g: Typ. 18±1.5 dBm @ 6 to 24 Mbps, Typ. 17±1.5 dBm @ 36 Mbps, Typ. 16±1.5 dBm @ 48 Mbps, Typ. 16±1.5 dBm @ 54 Mbps |
| RX Sensitivity | • 802.11b: -97 dBm @ 1 Mbps, -94 dBm @ 2 Mbps, -92 dBm @ 5.5 Mbps, -90 dBm @ 11 Mbps • 802.11g: -88 dBm @ 6 to 24 Mbps, -85 dBm @ 36 Mbps, -75 dBm @ 48 Mbps, -70 dBm @ 54 Mbps |
| • LAN | |
| Ethernet | • 4 switched 10/100 Mbps RJ45 ports • 1 optimized port for faster downstream communications with daisy-chained ioLogik E1200 units |
| Note | The optimized daisy-chain port is not supported by the ioLogik E1261W-T, E1261H-T, E1263H-T. |
| Protection | 1.5 kV magnetic isolation |
| Protocols | Modbus/TCP (slave), TCP/IP, UDP, DHCP, BOOTP, SNMP, HTTP, CGI, SNTP, SMTP |
| • Serial | |
| Interface | 2 RS-232/422/485 (software selectable) RJ45 ports |
| Parity | None, Odd, Even |
| Data Bits | 5, 6, 7, 8 |
| Stop Bits | 1, 2 |
| Flow Control | None, RTS/CTS, XON/XOFF |
| Baudrate | 300 to 115200 bps |
| Protocols | Modbus/RTU (master/gateway), serial tunnel mode (client/server) |
| • Physical Characteristics | |
| Wiring | I/O cable, 14 AWG (max.) |
| Dimensions | 61 x 157 x 115 mm (2.4 x 6.18 x 4.53 in) |
| Weight | Under 1265 g (2.79 lb) |
| Mounting | DIN rail (standard), wall (optional) |
| • Storage | |
| Expansion Slot | Up to 32 GB microSD™ memory card (SDHC compatible) |
| Note | For units operating in extreme temperatures, industrial-grade, wide-temperature SD cards are required. |
| • Environmental Limits | |
| Operating Temperature | Standard Models: -10 to 60°C (14 to 140°F) Wide Temp. Models: -30 to 70°C (-22 to 158°F) |
| Storage Temperature | -40 to 85°C (-40 to 185°F) |
| Ambient Relative Humidity | 5 to 95% (non-condensing) |
| Shock | IEC 60068-2-27 |
| Vibration | IEC 60068-2-6 |
| Altitude | Up to 2000 m |
| Note: Please contact Moxa if you require products guaranteed to function properly at higher altitudes. | |
| • Standards and Certifications | |
| Safety | UL 508 |
| EMC | EN 61000-6-2/6-4 |
| EMI | FCC Part 15B Class A |
| EMS | IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m IEC 61000-4-4 EFT: Power: 1 kV; Signal: 0.5 kV IEC 61000-4-5 Surge: Power 2 kV IEC 61000-4-6 CS: 3 V IEC 61000-4-8 |
| Radio | R&TTE: EN 62311, EN 300 328, EN 301 489-1, EN 301 489-17, EN 301 893; NCC; VCCI |
| Hazardous Location | Class 1 Division 2; ATEX Zone 2 |
| Green Product | RoHS, CRoHS, WEEE |
| Note: Please check Moxa’s website for the most up-to-date certification status. | |
| • Warranty | |
| Warranty Period | 5 years |
| Details | See www.moxa.com/warranty |
MOXA, Smart Remote I/O
ioLogik 2542-WL1
Features and Benefits
- Front-end intelligence with Click&Go Plus control logic, up to 48 rules
- Active communication with MX-AOPC UA Server
- Automatically complement disconnection period data with MX-AOPC UA Logger software
- 4-port unmanaged switch built in for linking to Ethernet devices
- I/O expansion port for daisy chaining up to 8 ioLogik E1200 units
- 3-in-1 RS-232/422/485 serial port for connecting to serial devices in the field
- Supports SNMPv1/v2c/v3
- Simplify I/O management with MXIO library for Windows Linux platforms
- Wide operating temperature range of -30 to 70°C (-22 to 158°F)
